Fire_spread_study_guidance

$ 5.00 — 11.00 AUD

I need to understand following type of questions

If you are avaialable for next 3 hours Kindly bid

I can pay AUD$11/hr rate so that You get AUD$33 for 3 hours

Questions samples are
QUESTION 1
1.
A fire is burning in a 30mx30mx5m (length, width, height) auditorium at the rate of 0.2kg/s and has a Carbon Monoxide Yield of 0.1.
Assume that the products of combustion are well mixed throughout the space and the density of air to be 1.2kg/m3:
a.
How long would it take for the hot layer to reach a Carbon Monoxide concentration that would lead to incapacitation after 5min exposure?

QUESTION 2
1.
A fire is burning in a 30mx30mx5m (length, width, height) auditorium at the rate of 0.2kg/s and has a Carbon Monoxide Yield of 0.1.
Assume that the products of combustion are well mixed throughout the space and the density of air to be 1.2kg/m3:
a.
How long before the Carbon Monoxide concentration was lethal after a very short exposure?

QUESTION 3
1.
Hot gases at 900˚C from a fire are flowing past a plasterboard wall whose exposed surface has already been heated to 100˚C, how much heat flux is transferred from the hot gases to the wall per square metre if the heat transfer coefficient is 15W/K m2?

QUESTION 4
1.
Hot gases at 900˚C from a fire are flowing past a plasterboard wall whose exposed surface has already been heated to 100˚C.
If the effective emissivity of the hot gases is 0.8 and the emissivity of the plasterboard wall is 0.9 in the above question, how much net radiant energy flux is transferred per square metre to the wall?

QUESTION 5
1.
An upholstered lounge which is burning in the middle of a room of a size of 5mx4mx3m (length, width, height) catches fire from a piloted ignition source.
Assuming that the diameter of the lounge is 1m calculate the size of the burning (Heat release rate) required for its flame to reach the ceiling level.

QUESTION 6
1.
An upholstered lounge burning in the middle of a room of a size of 5mx4mx3m (length, width, height) catches fire from a piloted ignition source.
If the heat of combustion of the lounge material is 18 kJ/g calculate the mass regression rate corresponding to the heat release rate estimated for Question 5.

QUESTION 7
1.
Calculate the time for a flame to spread from the bottom to top of a piece of paper 400 mm long held at an angle of 22.5o to the horizontal and also at an angle of 75o to the horizontal.
Provide a brief description as to why there is a difference in these times.

QUESTION 8
1.
In the AS1530.2 flammability test a 76 mm wide strip of material is subjected to ignition by a flame near the base of a 534 mm long vertical specimen in a laboratory at 20oC.
The flame reached the top of the specimen in 8 seconds.
a.i What is the rate of flame spread?
a.ii How long would it take for the flames to reach the top of a specimen that was twice as wide as the sample?

QUESTION 9
1.
If an illuminated exit sign emitted light at 200 Lux within a room filled with smoke at an optical density of 2 db/m, at what lighting level a person would see the illuminated exit sign?

QUESTION 10
1.
An old gas heater in a bathroom has developed a leak such that it is leaking gas (assumed to be Methane) at the rate of 0.15 kg every day.
Assume that the pilot flame of the heater is still burning and that the mixture in the room is well mixed.
If the bathroom is well sealed and
2. has dimensions of 3.5 m x 3 m x 2.4 m (length, width and height), how long would it take for ignition or explosion to occur?

EngineeringBuilding ArchitectureMechanical EngineeringChemical EngineeringFire Fighting

Similar Freelance jobs:

Cnc Programmer Busellato

CAD/CAMSolidworksMechanical EngineeringLabVIEWAssembly Place Bid

I'm looking for a programmer to program a Busellato Jet 3006 CNC Router - Genesis Software. Please reply ONLY if you are proficient and had knowledge with this machine. Thank you, Al

Full Description of CNC Programmer Busellato

I Need A Mechanical Engineer To Help Develop A Unique Roof Rack For Automobiles

EngineeringCAD/CAMSolidworksMechanical EngineeringProduct Design Place Bid

I am developing a unique roof rack designed to ease loading and unloading.

Full Description of I need a mechanical engineer to help develop…

Mechanical Design Engineer - Hvac System - Solidworks

SolidworksMechanical EngineeringProduct DesignAir ConditioningHeating Systems Place Bid

We have a base design of a hydroponic container farm, we need an expert to design the HVAC system that will fit into this design. We need you to bring in the most cutting edge solutions and calculations to maintain the energy consumption of our product to a minimum. Budget can be negotiated for the right talent.

Full Description of Mechanical Design Engineer - HVAC System - Solidworks

Natural Convection Project

EngineeringMechanical EngineeringPhysicsThermal AnalysisComputational Fluid Dynamics Place Bid

Project involves the study of natural convection within molten liquids

Full Description of Natural convection project

Mechanical Engineer -- 3

CAD/CAMSolidworksMechanical EngineeringManufacturing DesignProduct Design Place Bid

Looking for a Mechanical engineer that can help with an air filter. We can use axial fans to suit our needs (low cost, low wattage, low noise, high efficiency at ~75Pa pressure drop). All the centrifugal fans we have seen have a high pressure drop profile beyond our specs. The direction of flow wise, centrifugal fans would have kept design simpler so it was our first choice (contaminated air enters from the front and pure air leaves from the sides…

Full Description of Mechanical Engineer -- 3

I Need To Write A Blog Post

CopywritingBuilding ArchitectureTechnical WritingArticle WritingContent Writing Place Bid

1. What is your company name and URL? AOLISHENG ，www.aolisheng.us 2. What is your target market? occident 3. What type of content are you looking for? (Humorous/informative/general/promotional) Informative 4. What is the general theme or subject matter for the content? Heavy-duty drawer slide with a load of 220kg 5. What type of services do you offer? OEM,ODM 6. What products if any do you provide? 76 heavy drawer slides, 53 heavy drawer slides 7. Any other additional information that might…

Full Description of I need to write a blog post

I Need Staad Pro Structural Design For G+3 Building

CAD/CAMBuilding ArchitectureCivil EngineeringStructural EngineeringAutoCAD Place Bid

I need an experienced Staad Pro person to make a structural plan for a G + 3 Building in India.

Full Description of I need Staad Pro Structural design for G+3…

Scheme Of Ac/dc Adaptor -- 2

EngineeringElectronicsSoftware TestingElectrical EngineeringCircuit Design Place Bid

Searching for a specialist who has a little bit of free time and can design a scheme of properly working AC/DC adaptor (output 12VDC=2A) on Altium (included library and Gerber files). As the confirmation, that the adaptor works properly you will be asked a video demonstration, also the results of measurements. If some materials are needed for testing the scheme - we'll cover the cost. Find attached the photo of AC adaptor example.

Full Description of Scheme of AC/DC adaptor -- 2

Barcode Scan Reader - Basquet

EngineeringElectronicsElectrical EngineeringPCB LayoutCircuit Design Place Bid

I'm looking for an expert in Barcode Scan and electronics, I need a box with barcode readers inside this box to be able to read objects automatically. When I put one object into this box, this object should be identified using a barcode. This box should be able to identify this barcode in any position.

Full Description of Barcode scan reader - basquet

Rve Modeling Of Dual Phase Trip Steel (90% Maartensite And 10% Austenite)

EngineeringSolidworksMechanical EngineeringFinite Element Analysis3D Modelling Place Bid

need for stress strain curve and deformation simulation (ansys and abaqus)

Full Description of RVE modeling of dual phase TRIP steel (90%…

I Need Software Engineering Tutor

Engineering Place Bid

Give me a price for one session Topics 1- Introduction to Software engineering 2- Software process 3- Feasibility analysis 4- Software requirements 5- Applying use cases 6- System models 7- Architectural Design 8- Software testing

Full Description of I need software engineering tutor

Design Of Analog Discrete Time Fir Filter

EngineeringElectronicsVerilog / VHDLElectrical EngineeringCircuit Design Place Bid

I want layout of a circuit to be made on tanner (ledit).

Full Description of Design of analog discrete time FIR filter

I Need Digital Signal Processing Expert, Who Have Good Knowledge

EngineeringElectronicsElectrical EngineeringTelecommunications EngineeringDigital Signal Processing Place Bid

I need good expert who can do Digital Signal processing or signal and systems task

Full Description of I need Digital Signal Processing Expert, who have…

Lógica De Predicados (primer Orden) -- 2

EngineeringPrologMathematicsTeaching/LecturingEngineering Mathematics Place Bid

Necesito un freelacer que hable español y que sepa sobre Lógica de Predicados (Primer Orden)

Full Description of Lógica de Predicados (Primer Orden) -- 2

Dialux Design For Flood Light

EngineeringCAD/CAMMechanical EngineeringAutoCAD3D Modelling Place Bid

Dialux report confirming that two nos. of 300 W LED floodlight placed on a 8 mtr. Pole using cantilever of 1 mtr. Length on both sides of the pole are together able to provide minimum 7 lux in the area 25 mtr ( length) X 20 mtr (width) . please send me the price for the same. Thanks & Regards, [Removed by Freelancer.com]

Full Description of Dialux design For Flood light