Freertos, Microblaze, Reconos, Fpga, Hardware Accelerator

A design/prototyping group is needed to develop a neuromodulation audiovisual wearable device. The device has the form-factor of a sleep mask containing LEDs and earbuds to stimulate the brain with light and sound modulated with brainwave frequencies. The device controls the light and sound in accordance with a waveform (stored in an SD card). Required key capabilities include electronic product prototyping, PCP design, embedded SW, signal processing, audio file, low power devices, 32-bit MCU, mechanical closure, wearables and ergonomic devices,…

I need someone who can build a prototype for a Sitara SoC based streaming audio amplifier project. You must have a spectrum/distortion analyzer. Deliverable: Prototype hardware with firmware/software -Receive streaming Audio stack in ARM -Audio is output thru PRU-ICSS in Sitara via 10 bit PWM / 44 khz -integrated small power amplifier

Realization of a demonstrator on ST STM32F769I-DISCO board (4'' 480x800). STM32Cube - FreeRTOS – TouchGFX The application is defined (screens, sequences to screen or function). Reading one sensors on usart and other messages on canbus (defined messages). Show informations on GUI. Sending messages on canbus (defined messages). Save user's parameters in flash. Source full project Stm32Cube/gfx to deliver. Option: add bootloader IAP on USB to allow the program update (there are 2 flash banks of 1MB. Application is less than…

Arduino Bluetooth Controlled Car

Searching for a specialist who has a little bit of free time and can design a scheme of properly working Address engine control unit with integrated LIFEPO4 battery (with protocol management and testing) on Altium (included library and Gerber files). As the confirmation, that the module works properly you will be asked a video demonstration, also the results of testing. If some materials are needed for testing the scheme - we'll cover the cost.

Arduino Voice Controlled Car At Home

Arduino Obstacle Avoiding Car At Home

need to make a pcb shield for stm32 hz45zi-q board connection following modules 1) max 3865 temperature module ( 2 sets ) 2) Rdl 4-20 ma loop transmitter module ( with power connections ) 3) Eeprom 4) Rtc battery 5) memory card

electronics write a firmware in c ARM for a led display contact for more details

I am looking for someone to design a custom raspberry pi carrier board. The carrier board will have the following: 1. For use with the Raspberry Pi Compute Module 3+ 2. Solid state relay for control 3. 5v Barrel Jack connected for power 4. Wi-Fi Module 5. Ethernet RJ45 Connection 6. HDMI Connection 7. 1xUSB 3.0 Connection 8. Standard 40 pin GPIO Header The form factor of the board is important. Details Below: 1. Ethernet RJ45, Barrel Jack Connector and…

This is a project on PIC18F4550 using MIKRO C and physical components as well as Proteus (not 100% essential) From reading the text, designing the code and building it in physical. It´s an exam so it´s time measured and starts in 22 hours. (Thursday 24 at 07:00 am Mexico time) It lasts 3 hours I attach SAMPLE proyects and solutions, the project is really similar.

I am looking for someone to design a custom raspberry pi carrier board. The carrier board will have the following: 1. For use with the Raspberry Pi Compute Module 3+ 2. Solid state relay for control 3. 5v Barrel Jack connected for power 4. Wi-Fi Module 5. Ethernet RJ45 Connection 6. HDMI Connection 7. 1xUSB 3.0 Connection 8. Standard 40 pin GPIO Header The form factor of the board is important. Details Below: 1. Ethernet RJ45, Barrel Jack Connector and…

Required source code for temperature controller which has a selectable sensor such as RTD, J type, k type and with a selection of ON/OFF action or PID mode of operation. 3.5 inch touch control screen is used to display PV and SV value. Some other parameters like input voltage and load current is also displayed on touch screen with a edit-able option to display company name on touch screen. Also gives low voltage or high voltage alarm when the input…

Perform OTA update for ESP32 on GPRS using Quectel M66. Code to be done in Arduino. Firmware - .bin file to be downloaded from FTP/HTTP server over GPRS using Quectel M66.

To code a Secure Bootloader on the STM32L5 using the trustZone and STSFAE. The code must have several features to enhance the security. Code and data must be protected. The bootloader must use Active Tamper detection and Trustzone and Toot Security Services and pair of chip public/private keys and Secure Firmware Install. The code must be in C++14 The code must be properly commented There will be 5 milestones. Each milestone is released After satisfactory testing of the relevant milestone.…