Web|Software|Desktop|Mobile developers. Find a remote job.

I need a flutter app with the following functionality: connecting a ESP8266 to local wifi (also known as wifi provisioning). The connection should be done via "SmartConfig" SDK. Watch this video for details : https://youtu.be/5D6lkFGPPSw?t=131 . Source code is available for it. And make ESP8266 cave SSD and password to EPROM .

I am working on audio mesh network for music playback. I need an expert who can help me figure out latency issues

I need a flutter app with the following functionality: connecting a ESP8266 to local wifi (also known as wifi provisioning). The connection should be done via "SmartConfig" SDK. Watch this video for details : https://youtu.be/5D6lkFGPPSw?t=131 . Source code is available for it. And make ESP8266 cave SSD and password to EPROM .

i want app get real ip from esp8266 aftter finech config

help with this project https://github.com/SensorsIot/Wi-Fi-Sniffer-as-a-Human-detector Wi-Fi Sniffer as a Human detector want to add https rather then mqtt or some other way to see live tracking data of approaching devices and alllso add a way to log if a devices if found to be near or fowling the user ( radar}

i need a simple android phone app with a connect button plus two up buttons and two down buttons. I also need the esp32 sketch that the phone will control. I need each of the four buttons to be momentary contact that only pull the pins on the esp low while they are being pressed. each button has to control 2 pins at a time. at present i have a four relay module connected to the esp 32. the left…

I have a raspberry pi 4 SD image (128GB) all configured with Pi 4 (& all I need to do is for someone to run this on the 4GB Pi4 and use the built in “upgrade retropie software update” so that this will then work on the 8GB & 400 version, there should not need anything more than that to work, & then upload it so I can download this from you. If this is something you can do I…

I want smartwatch GUI code for ESP32, should be able to explain each of the logic, contact me further for more details of implementation logic

In our home automation system based on esp12, it connect with out server through post request and get request, and working fine but after some intervals , it give exception error we decode it and it shows:- Exception 28: LoadProhibited: A load referenced a page mapped with an attribute that does not permit loads PC: 0x40212708 EXCVADDR: 0x027d0210 Decoding stack results we want you to debug this error.

Create a filesystem management in Esp32 Internal Memory & send it to cloud through an API.

Development of a seismograph using ESP32 and freeRTOS APIs in arduino IDE. The system measures acceleration in 3D and velocities in X and Z. It writes the data to a microSD memory and sends the data to the cloud. So far everything is done. The project consists in the correction of the code to reach 100 Hz of sample rate. I am the developer and I need help from someone more experienced and work together over videoMeeting. The bill of…

This project is about measuring the amount of water in agriculture's soils using a matric potential sensor (200SS), a DS18B20 temperature sensor and an ESP32. It's an IoT development so the system is connected to the cloud, also has a LoRa module to communicate with the gateway and it's feeded using a PV solar panel. The overall project is not working as expected and I'm suspicious that something in the PCB is not correctly design, because I've tested the entire…

We have an ESP32 based project. The sensor is an MEMS microphone. We are collecting sound from MEMS and sending it to our server for analysis. We want to collect sound only of certain frequency to filter out other noise. We are looking for an embedded software engineer who already have experience in DSP on ESP32. What we already have: Code that is collecting sound from MEMS sensor (I2S) and sending it to our server. What we need: Add filters…

Hello everyone, Today I would like to have an arduino sketch done. Project assumptions: - GY-91 sensor (MPU9250), - Ublox NEO-M8N GPS, - motor control (https://github.com/thevolget/DBH1-Controller), - 2x 12V DC motor Required: Auto Calibration of the Magnetometer Filtering output of the sensors to convert them to Quaternions (Madgwick / Mahony / Kalman) Data Averaging Like this: https://github.com/kriswiner/MPU9250 I would like the GPS and sensor data to be linked so that the boat travels in a straight line. I would like…

My code crashes in some tasks, so this is a debugging problem. I am the developer and I need help from someone more experienced in ESP32 and freeRTOS so we work together over videoMeeting, so I can test your possible solutions in my hardware. The development is a seismograph using an ESP32 in arduino IDE. The system measures acceleration in 3D and velocities in X and Z. It writes the data to a microSD memory and sends the data to…